info@elefinetech.com Tel:+8613534079085
Boom barrier, Turnstile, Swing Turnstile, Fast Speed Turnstile, Parking System, Face Recognition Terminal, Face Reader, Temperature Measuring, Infrared Sensor, Mechanism, Motor, QR Code Reader, IC Card Reader
en
Products
Exhibition
New Promotion Boom Barrier Gate
New Promotion Boom Barrier Gate Up to 30% OFF
Elefine Brochure 2022
Shenzhen Elefine Technology Co., Ltd. Brochure 2022
Manufacturers Spot Microwave Radar Sensor Alarm Automatic Swing Door One-way Human Body Induction Switch Probe Mode

Microwave Radar Sensor Alarm Automatic Swing Door One-way Human Body Induction Switch Probe Mode

Model No.: EF-K12H

  • Wiring method: terminal insertion
  • 3C rated voltage range: below 50V
  • Induction mode: microwave induction
  • Delay time: 1.5s
  • Product series: sensors

Manufacturers Spot Microwave Radar Sensor Alarm Automatic Swing Door One-way Human Body Induction Switch Probe Mode

Microwave Radar Sensor Video:

Specifications:

  • Model No.: EF-K12H
  • Application range: automatic door swing door trash can door gate machine switch
  • Wiring method: terminal insertion
  • 3C rated voltage range: below 50V
  • Induction mode: microwave induction
  • Delay time: 1.5s
  • Product series: sensors

Technical Parameter:

  • Implementation technology: microwave and microwave processor
  • Transmission frequency: 24.125GHz
  • Transmit power: <20dBm EIRP
  • Emission frequency density: <5mW/cm²
  • Maximum installation height: 5 meters
  • Mounting inclination: 0-90 (portrait); -30 to +30 (horizontal)
  • Detection Mode: Motion
  • Minimum inspection speed: 50cm/s (along sensor longitudinal axis)
  • Power: <2W (VA)
  • Detection range (installation height = 2.2 meters): 4m (width) X2m (depth)
  • Power supply voltage: 12V to 30V AC/AD 30-10
  • Power frequency: 50 to 60HZ
  • Relay output (without initial potential): COM ON
  • Maximum contact voltage: 30V AC/DC
  • Maximum contact current: 1A (resistance)
  • Maximum switching power: 30W (DC) / 60VA (AC)
  • Temperature range: -20°C-+55°C
  • Protection class: IP54
  • Anti-interference performance: R><TTE 1999/5/EC EMC2004/108/EC
  • Shell material: ABS plastic
  • Shell color: black; silver gray
  • Shell size: 120mm (width) X80MM (height) X50MM (depth)
  • Weight: 0.215kg
  • Wire length: 2.5 meters

Microwave Radar Sensor Alarm Automatic Swing Door One-way Human Body Induction Switch Probe Mode

Features:

  • One-way motion sensor: when people walk towards the door, it senses, but when people leave, it does not sense
  • One-way sensor is suitable for hall glass automatic door, parking lot switch.

Installation:

Wall-mounted installation design, the product has a stylish and beautiful appearance, and can be directly fixed on the ceiling and wall.
Pry open the top cover, connect the internal wires, adjust the parameters, frame the screw holes in the picture, and fix them with screws.

Microwave Radar Sensor Alarm Automatic Swing Door One-way Human Body Induction Switch Probe Mode

Features:

  • Can be rotated left and right: The EAGLE antenna can adjust the declination angle left and right to determine the detected area.
  • German microwave sensor module: German microwave sensor module 24.15GHZ, with high stable emission frequency, not affected by temperature and humidity environmental factors, and reliable working performance.

Microwave Radar Sensor Alarm Automatic Swing Door One-way Human Body Induction Switch Probe Mode

Product introduction:

  • Indicator light: After the sensor is activated, the indicator light will flash for a few seconds. When the sensor detects motion, the indicator light is on
  • Sensitivity potentiometer
  • JST connector
  • Planar Antenna (Wide Detection Area)

Microwave Radar Sensor Alarm Automatic Swing Door One-way Human Body Induction Switch Probe Mode

Installation Precautions:

  • The sensor should be fixed tightly to prevent vibration,
  • Sensors cannot be mounted directly behind panels or other materials,
  • No movable or shaking objects can be placed in the detection area,
  • There should be no fluorescent source in the detection area,
  • Do not touch the electronic parts of the sensor directly,
  • When adjusting the sensitivity potentiometer, please apply light force and rotate slowly.

 



Leave a Message