Factory Price Metro Entrance Security RFID Reader Ticket Check in Barrier Gate Turnstile

Specifications:

• Model No.: EF-TB6005
• Material: stainless steel 304
• Length of the bar: 510mm
• Width of passage: ≤550mm
• Power supply: AC220±10%, 50Hz
• Open direction: single and double (optional)
• Work environment: indoor/outdoor
• Communication: TCP/IP
• Type: automatic /semi automatic
• OEM/ODM: yes
• Certificate: CE, FCC, ROHS
• Drive voltage: AC12V+AC18V
• Operation condition: -15°C~+60°C
• Relative humidity: None-condensation
• Input signal: 12v DC level or 12v pulse>100ms
• Working current: less than 2000mA
• Service life: ≥5 million
• Open angle: 120°
• Pass speed: less than 30 person/minutes
• Work environment: outdoor and indoor
• IP degree: IP45

Features:

• 1.Auto replacement function, re-position after person pass by
• 2.Anti tail function auto-lock once turn 120°
• 3.Arms auto drop when power off , insure unblocked when accident
• 4.Standard electronic interface, remote control through internet which is also could connect variety card readers and receive relay signal to work
• 5.Diverse control mode optional, changeable due to varying, convenient for your manage
• 6.Auto alert error function, comfort for user maintain and operate
• 7.Manual button or remote control ,Bio-directional passage
• 8.Open signal with memory or with out set function
• 9.Red and green light to show pass or stop, leisure to exit and entrance

How to install the intelligent three-roller gate?

In general, according to the left and right direction of the selected gate and the actual situation of the installation site, determine the installation position of the main gate of the gate. For non-concrete foundations or when the main body of the gate is installed with a slope, it is recommended to build a concrete foundation, and it should be ensured that the foundation and the foundation are firmly combined, and the perpendicularity of the main body of the three-bar gate to the horizontal plane is less than 1°.

Three roller gate installation process steps are as follows:

• (1) Pre-embedded lines: the position of the chassis is determined according to the customer’s requirements. If the concrete base needs to be poured, it can be completed in advance (the size of the base is about 100-150mm larger than the outer dimension of the bottom of the gate), and the chassis is fixed at the position Pre-buried or excavated cable trenches from the center point to the control room or sentry box, buried the line pipes, and penetrated the 2X1.5 square millimeter power lines and 4X0.5 square millimeters control lines used by the equipment. After confirmation, backfill concrete.
• (2) Fixing the chassis: Put the three-roller turnstile chassis in a fixed position, open the chassis door, and loosen the wing nut that fixes the cap (place the chassis door and cap carefully to avoid scratches on the surface). Then mark the center of the screw holes on the bottom plate of the chassis and the edge of the chassis base, remove the gate, and drill vertically with a drill bit on the marked screw holes (the size of the drill bit should match the expansion bolts provided with the equipment), The depth should meet the length requirements of the expansion screw. Move the chassis to its original position, drive in the expansion screws and fasten them firmly.
• (3) Installation of the brake lever: After the three-bar gate case is firmly fixed, the brake lever can be installed at the position of the lever handle, tightened with the provided screws, and ensure that the brake lever is not inclined. If you need to install the fork rod, after debugging the vertical and horizontal state, shake the brake rod to the horizontal position by hand, determine the installation position of the fork rod at the end of the brake rod, and fix the fork rod firmly with screws (no installation is required in the case of no fork rod). ). (4) Installation of peripheral equipment: The three-bar gate is firmly installed, and after the debugging is completed, according to the needs of the customer, the chassis circuit and the control circuit of the related peripheral equipment can be connected according to the wiring diagram of the gate control board, and the relevant debugging can be carried out.

Functions:

• 1. It has a clear function of indicating the direction of passage, and it is indicated by an intuitive arrow whether it is possible to pass (need to connect another direction light board).
• 2. With anti-tailing function: when each pass, the passing time is automatically canceled to prevent people from anti-tailing.
• 3. There are a variety of working modes to choose from, which can be one-way traffic, two-way traffic, and pass the signal to the main board to open the gate. (Need to be connected to another control system. Access control. Fingerprint, etc.) Control access, etc., can be set through the main board menu.
• 4. With automatic reset function: when the passer does not pass within the specified time after receiving the signal to open the gate, the system will automatically cancel the passer’s current pass authority, and the limited pass time can be set in the main board menu.
• 5. It has the function of power off and drop bar to meet the special needs of users and fire safety requirements.
• 6. The working mode of the directional electromagnet and the limit switch is adjustable to meet the needs of different customers. (The working mode of the directional electromagnet and the limit switch can be adjusted for high turnstiles).